– Connect the “TC” and “CG” terminals of the DLC3 connector. Reading codes (models with DLC3 connector) – The indicator should output the normal code (flashing 2 times per second). – Depress the brake pedal eight or more times in the interval of three seconds. – Connect the “TC” and “E1” terminals of the DLC1 connector (the car is stationary). Resetting codes (models with DLC1 connector) – Set the jumper on the “WA” and “WB” terminals. – Remove the jumper from the terminals “TC” and “E1”. – After 4 seconds, read the code by the number of indicator flashes. – Remove the jumper from the “WA” and “WB” terminals of the DLC1 connector.
– Connect the “TC” and “E1” terminals of the DLC1 connector. The self-test codes are read by the number of flashes of the “O / D OFF” indicator when the terminals “D11” under the bonnet or “TC” – “CG” of the DLC3 connector under the dashboard are closed and the ignition on (terminals up gear – “O / D OFF” is not lit).ģ7 – Input speed sensor for automatic transmission (P1705)ģ8 – The gauge of temperature of a working liquid АКППĤ2 – Speed sensor (or output speed sensor) (P0500)Ĥ4 – Speed sensor (or rear output speed sensor)Ĥ6 – Pressure accumulator pressure control solenoid (P1765)Ħ1 – Speed sensor (or front output speed sensor)Ħ4 – Torque converter lock solenoid (P0773)Ħ7 – Input speed sensor for automatic transmissionĦ8 – Torque converter clutch control solenoidħ3 – Interaxle differential lock solenoid Fault codes ABS (Toyota Hilux) Reading codes (models with DLC1 connector) 3 (P1310)ġ6 – Automatic transmission control systemġ9 – Accelerator pedal position sensor (P1120)ġ9 – Accelerator pedal position sensor (P1121)Ģ4 – Intake air temperature sensor (P0110)Ģ5 – Oxygen sensor – poor mix signal (P0171)ģ1 – Absolute pressure sensor (P0105, P0106)Ĥ1 – Throttle Position Sensor (P0120, P0121)Ĥ9 – Fuel pressure sensor (D-4) (P0190, P0191)ĥ8 – Drive SCV (D-4) (P1415, P1416, P1653)Ĩ9 – Drive ETCS (P1125, P1126, P1127, P1128, P1129, P1633)ĩ7 – Nozzles (D-4) (P1215) Diesel engine trouble codes (Toyota)ġ4 – The valve of adjustment of a corner of an advancing of injectionĢ2 – The gauge of temperature of a cooling liquidĩ6 – EGR Valve Position Sensor Transmission fault codes of Toyota Hilux In the presence of two or more codes, a pause between them is 2.5 seconds.Īfter the output of all codes, there is a pause of 4.5 seconds, and then the codes are repeated.ġ3 – Crankshaft Position Sensor (P0335, P1335)ġ4 – Ignition system, coil No. If there is a malfunction, the indicator gives the beginning of the tens in 0.5 seconds, then a pause of 1.5 seconds and a unit with a pause of 0.5 seconds. If there is no malfunction, the indicator flashes at 0.25 second. The DLC2 connector is also closed in it “TE1” – “E1”. The self-diagnosis codes are read by the number of flashes of the indicator “CHECK ENGINE” with the closed terminals “TE1” – “E1” of the DLC1 connector under the hood or “TC” – “CG” of the DLC3 connector under the dashboard and the ignition on.
Toyota Hilux Fault codes of petrol engines (Toyota)
0 kommentar(er)
